* Look over the battery chargers we sell on this page. We sell universal use battery
chargers for nearly all scooters. All you need to know is how many 12 volt batteries
are installed in your scooter to determine the voltage of the electrical system
(two 12 volt batteries would be a 24 volt system). Most scooters use lead acid batteries, but some use Lithium. Chargers should always match the type batteries used. Our chargers are for Lead-Acid battery sets unless stated otherwise.
* Find a charger that matches your scooter's battery electrical system 12, 24, 36, or 48 volts
beginning at the top of the page and scrolling down until you find a charger of the correct
voltage (they are all standard AC input) for charging 12, 24, 36, etc output and the connector
mates to your scooter charge receptacle. The most common charger plug is a 3 prong female
type that mates with a three pin male receptacle, but other plugs are also used and pictured/described.
* Note that battery charger output DC voltage is alway slightly higher than the system voltage so
that, for example, a 24 volt charger would output 29 volts in order to charge the battery set of
two 12 volt batteries connected together in series. With this information you should find a
charger that will charge your batteries and automatically turn off when finished.
* Electrical components are not covered by warranty for return to exchange or for refund. Parts are tested prior to packaging for correct operational condition.
3 prong Female Plug, 12 Volt
Lead-Acid Battery Charger For Gas and Electric Scooters with
three prong socket Receptacles (90-245V AC with
16.5V DC 1.0A Output) $14.95
plus shipping/handling 
Intelligent Lead-Acid Battery Charger provides current to battery set at
correct amount to charge without overheating, shut off when
batteries are charged. Choice of connector.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X-10 and X-140 24V Lead-Acid Battery Charger, replaces old style
Battery Charger which was prone to failure and overcharged
batteries. New Intelligent X-10 and X-140 scooter Lead-Acid Battery Chargers
automatically charge batteries at a rate that will not damage
batteries and shuts off to prevent overcharging or charger failure
- High Quality, same single pin connector for X-10/X-140 Scooters plus
others like Sharper Image and Izip 130 - $22.95
plus shipping/handling
3.5mm Single pin female connection to scooter charger input
port.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Battery Charger INPUT PORT - $9.95
plus shipping/handling Regular
$14.95
3.5mm Single pin male connector receptacle for x010 Battery Charger
input.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
CONNECTOR PLUG, 3.5MM - $7.95
plus shipping/handling. Regular Retail
Price less shipping $14.95
3.5mm Single pin female connector plug for x010 and other scooters
Battery Charger input.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
24 volt, 2 or 3 prong OEM Lead-Acid Battery Charger
for the model X-11 or X-250 X-treme scooters and other models $58.95
Plus Shipping/Handling
Intelligent charger provides current to battery set at correct
amount to charge without overheating, shut off when batteries are
charged. Indicator light shows charging and when charged. WE NOW SHIP THE 24 VOLT 3 PIN CHARGER WITH THE MATCHING 3 PIN MALE SOCKET BECAUSE THE 2 PIN X-TREME OEM CHARGER IS NO LONGER AVAILABLE. The socket easily installs in place of the old 2 pin socket and still uses only 2 of the three pins.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
24 VOLT
MOST POPULAR 24 VOLT Lead-Acid Battery Charger, 3 Prong Plug. $17.95
(90-245V AC with 29.5V DC 1.6 Amp Output)
Use with all 24 volt, 3 prong scooters with either standard female
connector or XLR Male Connector, connected and ready to use.
This charger is superior to most sold scooter chargers because it
has a fuse that can be changed if blown due to overload or short.
The case can be opened, unlike most others, and the fuse replaced.
But if your socket is different it can still be used by replacing
the socket on the scooter. Need a socket? See it available
separately.
plus shipping/handling
Charger indicates red when charging and green when fully charged.
May be used with two prong Battery Charger connectors by using the
old two prong plug from the previous Battery Charger. Only two of
the three pins are used in three prong chargers (pin 1 is always
positive).
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
24 Volt, 3 Prong Male XLR Connector -
$34.95
(100-240V AC with +24V DC 1.6 Amp Output)
plus shipping/handling
OEM 24 volt, three MALE prong Battery Charger as used on many Scooters
including Schwinn, Mongoose, GT, and Currie. Charger with indicator
light shows when charging and fully charged. Matches socket below.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Lead-Acid Battery Charger, Europe Plug, 24
Volt, 3 Prong Female Plug. $24.95
(90-245V AC with 29.5V DC 1.6 Amp Output)
Use with AC oulets in Europe only (
American version above). For all 24 volt, 3 prong scooters
with 3 pin male sockets. This charger is superior to most sold
scooter chargers because it has a fuse that can be changed if blown
due to overload or short. The case can be opened, unlike most
others, and the fuse replaced. But if your socket is different it
can still be used by replacing the socket on the scooter. Need a
socket? See it available separately.
plus shipping/handling
Charger indicates red when charging and green when fully charged.
May be used with two prong Battery Charger connectors by using the
old two prong plug from the previous Battery Charger. Only two of
the three pins are used in three prong chargers (pin 1 is always
positive).
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
24 VOLT
LITHIUM ION BATTERY CHARGER, 3 Prong Plug Choice. $39.95
(DC 2 Amp Output)
Use with all 24 volt Lithium Battery sets, 3 prong scooters with either standard female
connector or XLR Male Connector, ready to use.
This charger is made for Lithium Ion battery set charging only. Fan cooled.
plus shipping/handling
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
MOST POPULAR 36 VOLT Lead-Acid Battery Charger, 3 Prong Connector For
$19.95
(90-245V AC with 42.6V DC 1.6 Amp Output). Same charger as used on some X360 Scooters when 3 pin female connector is selected in the drop down menu.
plus shipping/handling
36 volt, three prong Lead-Acid Battery Charger with either standard female
connector or XLR Male Connector, connected and ready to use. Charger with indicator light shows
when charging and fully charged. May be used with two prong Battery
Charger connectors by using the old two prong plug from the
previous Battery Charger. Or purchase the three prong socket below
for replacement to match this Battery Charger connector.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
36 volt X-treme's OEM (Original Equipment Manufactured) Lead-Acid Battery Charger and Socket for the X-treme X360 and other
scooters with 2 OR 3 prong male sockets on the scooter. $64.95
Plus Shipping and Handling
Intelligent Lead-Acid Battery Charger provides current to battery set at
correct amount to charge without overheating, shut off when
batteries are charged. Indicator light shows red during charge,
green when charged. WE NOW SHIP THE 36 VOLT 3 PIN CHARGER WITH THE MATCHING 3 PIN MALE SOCKET IN PLACE OF THE 2 PIN VERSION BECAUSE THE OEM 2 PIN CHARGER IS NO LONGER AVAILABLE. The socket easily installs in place of the old 2 pin socket and still uses only 2 of the three pins.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
36 Volt, 3 Prong Male XLR Connector -
$39.95
(100-240V AC with 41.8V DC 1.6 Amp Output)
plus shipping/handling
36 volt, three MALE prong Battery Charger as used on many Scooters
including some X-treme Models, MX500, etc. Charger with indicator
light shows when charging and fully charged. Matches socket below.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Battery Charger Receptacle, two prong male
$16.95
for X-treme X11, X360 models and many others.
Plus shipping/handling.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
3 Prong Battery Charger Receptacle.
Replaces the 3 pin male receptacle on the Scooter $8.95
plus shipping/handling
Standard male 3 pin receptacle socket to receive the female three
pin Battery Charger plug of most Electric Scooters including Vapor
Scooters. Replacement for any make Scooter, may require splicing to
your existing wiring connectors to your control box.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
3 Prong Female Socket For $11.95
plus shipping/handling
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
3 Prong Battery Charger
Plug
Replaces the standard female or male XLR plug on the Scooter Battery Charger cord
$5.95
plus shipping/handling
Standard three pin Scooter Battery Charger plug of
most Electric Scooters including Rad2Go, Razor, Vapor and X-treme
Scooters.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
48 Volt 3 Amp Fan Cooled
Lead-Acid Battery Charger, Choice of Panterra Polarity or Standard Polarity
PC Style Female Connectors, $79.95
plus shipping/handling
Intelligent 48 volt, three prong PC Style connector plug, Fan
Cooled, Intelligent Lead Acid Battery Charger with 100-240V AC input with 53.5V DC
output (for 48 volt battery set) and up to 3 Amps Output. Charger with two indicator lights show when
charging and fully charged. Polarity for most Pantera scooters or
standard scooter polarity. Usual Panterra Polarity (N=Negative, L=Positive), Standard Polarity (N=Positive, L=Negative) where the PC plug is marked with N and L at the connectors.
Charger Indicator pictures for charging and charged state.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
48 Volt 2.5/3 Amp Fan Cooled
Lead-Acid Battery Charger, Choice of Connector, $79.95
plus shipping/handling
Intelligent 48 volt, three prong round connector plug
(matches the sockets on this page), Fan Cooled, Intelligent Battery
Charger with 100-240V AC with 53.5V DC 2.5 Amp Output. Charger with
two indicator lights show when charging and fully charged. If your
socket is different it can still be used by replacing the socket on
the scooter with the matching socket sold here, or by splicing or
soldering on your old charger's plug. Plug polarity is indicated on
the case of the charger as the normal Pin 1 positive. Your choice
of standard 3 pin round female connector or XLR 3 pin male connector.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
48 Volt Lithium LiPo4 Fan Cooled
OEM Battery Charger $107.95
plus shipping/handling
Intelligent 48 volt, three prong connector plug, Fan Cooled, Heavy Duty Lithium LiPo4 Battery
Charger with 100-240V AC input. Charger with
indicator lights show when charging and fully charged. Not compatible with LIMN battery sets.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
60 Volt 1.6 Amp Lead Acid Fan Cooled
Battery Charger $69.95
plus shipping/handling
Intelligent 48 volt, three prong connector plug, Fan Cooled, Heavy Duty Lead Acid Battery
Charger with 100-240V AC input. Charger with
indicator lights show when charging and fully charged. Choice of output connectors.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
60 Volt 2.5 Amp Lead Acid Fan Cooled
Battery Charger $99.95
plus shipping/handling
Intelligent 48 volt, three prong connector plug, Fan Cooled, Heavy Duty Lead Acid Battery
Charger with 100-240V AC input. Charger with
indicator lights show when charging and fully charged. Choice of output connectors.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Heavy Duty 48 Volt 9 Amp
POPULAR Lead-Acid Battery Charger For $174.95
48V Fan Cooled Charger for large electric scooters like the
Panterra. Amperage output is up to 9 Amps. Fast charge use for
Panterra (Freedom electric), Panterra (Fusion electric), Panterra
(Retro Electric), and Various makes/models of electric scooters of
different connection polarities. Fan cooled for heavy duty use,
fuse protected. Pretested in load environment for a 48 volt battery set.
Also, a standard scooter polarity version of this same charger for many
brands of scooters using this type connector. Usual Panterra Polarity (N=Negative, L=Positive), Standard Polarity (N=Positive, L=Negative) where the PC plug is marked with N and L at the connectors.
And we can attach a 3 prong round female connector (Pin 1 is positive) in place of the PC Style connector when you order it separately and ask us in the message area to attach the connector. No charge for labor. Order the connector above if needed.
plus shipping/handling Availability of this
item?
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
3 Prong PC Style Battery Charger Receptacle.
Replaces the male receptacle on the Scooter $7.95
plus shipping/handling
PC Style male 3 pin receptacle socket to receive the female three
pin Battery Charger PC Style plug of most Electric Scooters. Replacement for any make Scooter, may require splicing or soldering to
your existing wiring connectors to your control box.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
PICTURES OF REPLACEMENT PARTS MAY VARY PRIOR TO UPDATES. PARTS ARE PROVIDED IN AS-IS CONDITION WITH NO REGARD TO SLIGHT COSMETIC IMPERFECTIONS DUE TO STORAGE OR HANDLING, AND PRODUCTION RUNS MAY SLIGHTLY ALTER THE APPEARANCE OF THE SAME PART FROM TIME TO TIME MAKING SLIGHT DIFFERENCES FOR MATCHING OF SEVERAL ITEMS IN AN ORDER (WHENEVER POSSIBLE WE MATCH AS CLOSELY AS POSSIBLE FOR ORDERS WHERE CUSTOMERS REQUEST THIS). ALL PARTS ARE INSPECTED AND TESTED AS POSSIBLE FOR QUALITY CONTROL PRIOR TO PACKAGING AND SHIPMENT OF CUSTOMER ORDERS. ALL SALES ARE FINAL WITH THE EXCEPTION OF NON-ELECTRICAL ITEM EXCHANGES FOLLOWING OUR TERMS OF SALE ORDER POLICIES FOR THE ORDERING OF INCORRECT PARTS. CUSTOMERS SHOULD ALWAYS TAKE ADVANTAGE OF OUR 24/7 EMAIL AND OTHER COMMUNCIATIONS FOR HELP PRIOR TO PLACING ORDERS, IF NEEDED. USA STANDARD SHIPPING IS INCLUDED IN THE PRICE OF PARTS ONCE ADDED TO THE SHOPPING CART THAT ALSO REPRESENTS THE HANDLING FEE FOR INTERNATIONAL ORDERS. INTERNATIONAL SHIPPING IS SEPARATE FOR EACH ORDER BASED ON INFORMATION PROVIDED ON OUR 'HOW TO PLACE AN ORDER' PAGE USING THE LINK IN THE ITEM DESCRIPTION. USA HANDLING IS ADDED TO EACH ORDER DURING CHECK-OUT TO ADJUST SHIPPING AND PROCESSING OF EACH USA ORDER. PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND CUSTOMER WILL BE ADVISED IN THAT EVENT.
SUMMARY:
A Scooter Battery Charger is typically
24 or 36 volts, with some 12 volt or 48 volt. Our Scooter
Battery Chargers are intelligent, charging at a rate that will
not heat damage the batteries and shutting off when the battery set
has fully charged. Bottom line - Get the best
Scooter Battery
Charger shipped to your door in 1-2 days in the USA.
SCOOTER BATTERY
CHARGER
